Blog

Water Heater Repair Philadelphia Blog

Our blog is designed to give homeowners as much information on general plumbing repair tips, not just Philadelphia water heater repair advice.  Many home plumbing maintenance tasks homeowners can be well equipped  to take care of themselves.  Enjoy!

Water Heater Energy Efficiency Tips

Posted by on Jun 13, 2014 in Water Heater Repair Philadelphia | 0 comments

Few of our customers at Water Heater Repair Philadelphia do not want to be as energy effective as possible with all of their residence expenditures, including their water heating expense. So, we chose to put together a list of things that will certainly make homeowners do just that.Water Heater Repair Philadelphia

energysavers.gov estimates that 14-25 % of a house’s energy use is from heating water, and it also comprises some of the electric bill too. The following suggestions will certainly make make best use of ones water heater’s efficiency.

  • Depending upon the quantity and frequency of the need for hot water, a tankless water heater might be a good investment come time to have a water heater replacement. They are more pricey than traditional storage tank water heaters, however over the lifetime of the system can be more cost effective. Not to mention the potential energy savings of running the tankless water heater.
  • If the temperature of the heater is set above 120 degrees, lowering it can save some energy usage too.
  • If one is lucky enough to be constructing a new home or doing a remodel, try to position the water heater as close the area of the home that will certainly utilize the most hot water. Water heat lost while flowing through the water pipes will certainly be lessened.
  • A solar water heater could be a good investment too, and not as dependent upon the area of the country one lives in as most people would believe. Heck, one can even make one with the quantity of details online, though as plumbing technicians ourselves, we would love to assist.
  • Insulate, insulate and insulate some more. All uncovered water pipes, not only the hot water ones, need to be wrapped with insulation. One can consider utilizing a water heater jacket or blanket in the winter period to assist keep the heat inside the storage tank. New tank water heaters are made well with a nice insulation value, but every bit will certainly help.
  • This could be difficult to do (at least I know it would be in my house with several women) but take much shorter showers.
  • When replacing a water heater, see to it it is the proper size for the quantity of water that will be made use of typically. Often times we see that house owners have too big of a water heater, which raises the quantity of energy needed to heat up the water … and water that will not be made use of.

Philadelphia water heaters are fairly repair free but a yearly examination and some small maintenance will certainly help lengthen its life expectancy and save cash with it performing at optimal performance. Give us a call to schedule an annual check.

 

Philadelphia Water Heater Carbon Monoxide Prevention

Posted by on Jun 6, 2014 in Water Heater Repair Philadelphia, Water Heater Safety | 0 comments

We have recently seen a number of news reports about carbon monoxide gas poising being connected back to a water heater as the source and so felt it important to write some about that potential today. Yes, any nonrenewable fuel source burning appliance creates this fatal gas. Consisting of hot water heaters. Nevertheless, with the proper installation of the water heater, together with routine maintenance, and a working carbon monoxide gas detector in the home, one can sleep safely.

Causes of Carbon Monoxide PoisoningWater Heater Repair Philadelphia

Carbon monoxide gas (CO) is a colorless, odor free gas that is a bi-product of the burning of a fossil fuel like wood, gasoline, coal, natural gas, or kerosene. Breathing in carbon monoxide fumes not only prevents oxygen from being utilized appropriately by the body, but likewise causes damage to the central nervous system. Persons with existing wellness problems such as heart and lung illness are particularly vulnerable, as are infants, youngsters, pregnant women, and seniors.

Sources of Carbon Monoxide Gas

The cold weather heating period is when a bulk of carbon monoxide exposures take place due to using unvented supplemental heaters. An unvented supplemental heater is a kind of space heater that makes use of indoor air for heating and vents the gases produced in the heating process out into the home. Many heaters of this kind use kerosene or natural gas for fuel. While more recent designs have oxygen sensors that shut off the heater when the oxygen level in the area falls below a certain level, older designs do not have such safety functions. Because of these safety issues, unvented space heaters have actually been prohibited in numerous states. Other sources of carbon monoxide gas are malfunctioning cooking devices, tobacco smoke, obstructed chimneys, car exhaust, malfunctioning furnaces and gas clothes dryers, wood burning fireplaces, and a hot water heater.

Symptoms of Carbon Monoxide Gas Poisoning

Below are the most typical signs of carbon monoxide poisoning but they are not constantly the very same for each individual who has been exposed and often times resemble having food poisoning or the flu. A physician can assist in identifying for sure.

headache
dizziness
weakness
queasiness and throwing up
rapid heartbeat
seizures
cardiac arrest
loss of hearing
fuzzy vision
disorientation
loss of consciousness or coma
respiratory failure

Defense By Proper Gas Appliance Venting

The CDC provides the following information on preventing CO2 poisoning by making certain ones home appliances are vented correctly.

  • All gas appliances must be vented so that CO will not build up in your home, cabin, or camper.
  • Never burn anything in a stove or fireplace that isn’t vented.
  • Have your chimney checked or cleaned every year. Chimneys can be blocked by debris. This can cause CO to build up inside your home or cabin.
  • Never patch a vent pipe with tape, gum, or something else. This kind of patch can make CO build up in your home, cabin, or camper.
  • Horizontal vent pipes to fuel appliances should not be perfectly level. Indoor vent pipes should go up slightly as they go toward outdoors. This helps prevent CO or other gases from leaking if the joints or pipes aren’t fitted tightly.  (read more…)

It is definitely crucial to have CO2 detectors in the home. The Colorado State University Extension provides the following tips when picking a CO2 alarm.

  • Some inexpensive alarms consist of a card with a spot (spot detectors) that changes color in the presence of CO. The absence of an audible signal does not meet UL or IAS requirements for alarms, so these devices do not provide adequate warning of CO.
  • Some CO alarms have a sensor that must be replaced every year or so. The expense of this part should be a factor in purchase decisions.
  • Battery-operated alarms are portable and will function during a power failure, which is when emergency heating might be used. Batteries must be replaced, although some alarms have long-life batteries that will last up to five years.
  • Line-powered alarms (110 volt) require electrical outlets but do not need batteries. They will not function during a power failure. Some line-powered alarms have battery backups.
  • Some alarms have digital readouts indicating CO levels. Alarms with memories can help document and correct CO problems.  (read more…)

The following video gives some nice safety tips for water heaters.

Not to frighten anyone, but we also wanted to include the following video of a water heater set up that is not working correctly and is harmful.

Please see a doctor promptly if you suspect that you or a member of your family might have carbon monoxide poisoning. Water Heater Repair Philadelphia can not stress enough the requirement of ensuring a professional plumbing repair business services and installs any water heater equipment in your home or business.

Replacing a Heating Element in a Philadelphia Water Heater

Posted by on May 20, 2014 in Water Heater Repair Philadelphia | 0 comments

If your water is not heating appropriately and you think a defective heating element follow these seven steps on screening and changing it. Bad elements are common troubles specifically in older water heaters that have actually been in a few years. This can take place to a more recent heater also. This is easily diagnosed and replace it could need a little perseverance.

Water Heater Repair Philadelphia

Note: It is best to have a trained plumbing professional perform these steps. Water Heater Repair Philadelphia just wanted to share the process for doing with our readers.

Tools needed: Ohm/Volt meter, heating element socket, [both of which can be purchased at a hardware shop], screw vehicle drivers Phillips and flat head.

Step one: Heating elements that go bad are quickly detected by first shutting off the power to the heater then removing the access covers one at a time and examining each element separately. This will likewise work on loud elements, ones that have calcium buildup. The access covers are usually on the side of the tank one on top one on the bottom. Turn supply of water off and drain the tank unless one is experienced at changing elements with a complete tank.

Step Two: After eliminating the leading access cover, get rid of the insulation that is behind it this should have been cut at the factory. The insulation will come right out. Then raise the plastic cover to expose the element. This will be on the bottom half of the cover.

Step Three: Eliminate one wire off the element and afterwards put the meter on ohms and touch both contacts to see if it reads. If it does not read the element is probably bad and requires replacing. If it reads then continue to examine the next one. In electric water heaters there is a bottom and a top element.

Step Four: After determining where the bad element is remove both wires ensuring the power is off. Put the element socket on a cog and turn the element counter clockwise removing it. Some force might have to be put into this.

Step Four: Put the Gasket on the new element and hand tighten where the old element was and turn clockwise until tight. Complete tightening the element with the cog.

Step Five: Put the wires back on ensuring they are snug.

Step 6: Fill the tank with water opening the hot water valves in the house to draw out air from the lines. Remove aerators on any faucets that are open and put them back on when finished. After the water is flowing in the sink or tub turn it off. Check for leaks after this is done.

Precaution: Do not turn the power on before the tank is complete or another element could be damaged.

Step Seven: Turn the electrical power back on put the insulation and covers back on. The hot water problem will be fixed.

Don’t hesitate to contact Water Heater Repair Philadelphia PA with any questions you may have.

Resources:

How to Repair an Electric Water Heater

Electric Water Heater Element Tests

How to Test a Water Heater Element Video

 

Enhanced by Zemanta

Sizing A New Philadelphia Water Heater

Posted by on Apr 23, 2014 in Water Heater Replacement Philadelphia | 0 comments

Shopping around for a new water heater? For lots of people, it is not the most enjoyable kind of shopping to do, and for most people it might not be the easiest. The majority of water heater repair companies will definitely do a good job of making good pointers for ones options. If one is inclined to do some more in depth research oneself, below are some links that will be useful.

Energy Cost Calculators
The U.S. Department of Energy has an energy cost calculator for electric and gas type water heaters on its website that is useful. It may appear a little challenging, however one need to have the ability to fill out the majority of the fields and get an approximation of just how much it will cost to run the heater.

Water Heater SizingWater Heater Repair Philadelphia
Many of the producers of water heaters have sizing calculators on their websites to identify what the proper size heater will be considering the amount of water to be heated up at peak times of the day. Here are links to A.O. Smith  and Bradford White.

Many gas companies have good tools on their websites to determine expenses also. Check with your local gas or electric company to see exactly what they have published. Also, here is a cool tool from the River Network in Portland, OR that will examine the energy and greenhouse gas emissions for any place in the United States.

Do not think twice to call Water Heater Repair Philadelphia with any concerns you may particularly have with determining the very best size water heater for your Philadelphia home.

Check out our Water Heater Replacement Philadelphia page too…

How to Prevent Philadelphia Water Heater Repairs

Posted by on Apr 1, 2014 in Water Heater Repair Philadelphia, Water Heater Replacement Philadelphia | 0 comments

Most don’t ever think about the state of their water heater Water Heater Repair Philadelphia knows. Understandably so, as long as it is functioning properly. However, a little water heater service can go a long way toward minimizing the number and frequency of repairs, and really helps to extend the life of the heater, avoiding very early replacement. Learn how keeping your water heater can affect its life expectancy and provide you less stunning minutes of cold water.

A Healthy Philadelphia Water HeaterWater Heater Repair Philadelphia

While nobody can figure out specifically how long a water heater ought to last, an effectively preserved, quality water heater can last 8 to 10 years. Obviously, many elements will affect the life-span, consisting of electrical energy abnormalities, the quality of the water heater, and the mineral density of ones water. Regular water heater maintenance can likewise lower electric expenses by having it function more efficiently

Among the quickest killers of water heaters is mineral buildup. A great deal of cash is spent replacing heating elements and entire tanks, when some service over the years would help to avoid this expense from happening. A healthy water heater is one that is insulated, clean, and without electrical wiring faults.

Troubles with ones water heater usually become self-evident: A hot water faucet fails to bring hot water, you see leaking or puddles near the storage tank, or the tank discharges strange gurgling or popping sounds. These are a few sign telling you when your hot water heater requires changing.

It would be good to know before your water heater springs a leakage and triggers a trouble or worse yet damage to your home. If you identify you have some of the early caution signs you will have time to examine your selections of sizes and models and select a qualified installer as opposed to hurrying to find a replacement water heater on a Friday afternoon or even worse on a weekend.

Here are some indications that you could be ready for a new hot water heater

Age: On average, your gas hot water heater need to last anywhere in between 8 to 12 years, while an electric model will last a bit longer at 10 to 15 years.
Discolored Water: When you use your hot water tap, does the water look a bit tinted? If so, there might be rust in your water heater, which is a possible indicator your hot water heater is showing signs of wear and may start to leak.
Banging or Popping: When there is a buildup of hard water sediment in the water heater,it might could sound like explosions. These noises are triggered by the difference in water temperature inside the tank as incoming cold water mixes with the heated water of the tank.
Moisture: Look around the base of the water heater for wetness, for this could be a symptom of a sluggish or intermittent leak.
Cold Water: An unexpected cold shower is not just bad means to start your day, however of a hot water heater that has to be examined out.
Major Water Leaks: It’s time to call Water Heater Repair Philadelphia now.

Philadelphia Water Heater Maintenance in 10 Minutes

Posted by on Feb 25, 2014 in Water Heater Repair Philadelphia | 0 comments

We are going to put you to work today, but just for about 10 minutes. Yep, that’s all it will consider these 2 essential water heater upkeep tasks; however, Water Heater Repair Philadelphia understands they will do an outstanding task of helping with 3 things:
Having your water heater last as long as possible (that will conserve you cash).
Making sure the water heater runs safely (we do not want it to blow up).
Having it run as energy efficiently as possible (likewise conserving you cash).

So with that in mind, are you ready to invest 10 minutes once or twice a year to help conserve some money? Water Heater Repair Philadelphia PA thought so.

Testing the T&P Relief Valve

Typically called the T&P Valve, or the temperature and pressure relief valve, has a vital job. It helps ensure excess pressure does not develop inside the water storage tank, or in much more basic terms, it sees to it the water heater does not blow up. As the picture shows, it has a lever or little manage on it. All you have to do is raise it part means and then let go of it. Ideally, it snapped back to its shut position quickly. If it is working correctly, a little water can be heard entering into the drain pipe below the lever you just lifted and you possibly heard some pressure being released. If none of these things have actually happened throughout the test, the valve will need to be replaced.

Do a Mimi Water Heater Tank Flush

By nature, rust and rust will happen inside the water storage tank thanks to the chemical reactions taking place with all the components inside that are required to warm the water. We will not get too technical right here, but it is easy to assist avoid this process by doing a flush or draining of all or a portion of the water in the tank.

For just a mini flush, position a bucket under the drain valve below the tank. Open the drain valve and fill up the bucket with water. Drain a minimum of a few gallons of water in total. Let the water sit in the pail for a few minutes to settle and analyze if there is much that settles to the bottom of the bucket. If there is, if the water heater has actually not been drained for a long period of time (or ever), it would be best to do a full flush of the tank to get as much of the sediment out as possible. You will wish to turn the temperature dial down and might want to let the water cool off for about an hour initially so it is not too hot while draining it. Also, it would be simpler to attach a hose to the drain valve and let the water go outside instead of utilizing buckets.

If the water looks reasonably clean and clear from the tiny test you should be all set. When the water heater has a large quantity of sediment inside of it, it can make loud popping noises and it cuts down on its effectiveness too.

Though water heaters are fairly maintenance free and not hard to run, whenever you feel the slightest uneasy or are not sure of what to do, it is always best to have a plumbing professional assist with the circumstance.

Water Heater Repair Philadelphia

Water Heater Venting Techniques

Posted by on Feb 18, 2014 in Gas Water Heater Repair Philadelphia, Water Heater Repair Philadelphia, Water Heater Replacement Philadelphia | 0 comments

Water Heater Repair Philadelphia is talking about the following ideas about proper water heater venting for property owners to have a basic understanding of how the different types of venting work. They are not planned to be how-to directions for property owners to perform themselves. The training and licensing of an expert plumbing repair service specialist is always extremely important.Water Heater Repair Philadelphia

As far as gas water heaters go, there are 2 popular venting choices: direct vent water heaters and power vent water heaters. Relying on which type of system one uses will rely on the direction the vent is installed from the water heater to the outdoors so the dangerous gases produced from the water heater’s burner are not launched inside the house, but rather sent out into the outside atmosphere. You may have heard the term atmospheric water heater while looking at different types of kinds of water heaters. Likewise, air should be sent out into the water heater for combustion to take place.

This video gives some tasks to perform to help see if your water heater is currently properly vented:

Direct Vent Water Heaters
It is optimal if the air needed for combustion is from outside the house in order to minimize the danger of fires from the flammable vapors of the water heater. The air from outside the home will either be vented out a wall or the roof of the home. Direct vent systems will help address the issue of not having enough indoor ventilation by drawing in air from outside your house.

The fundamental concepts of a direct vent water heater is that the heat produced from the burning of fuel is used to heat up the water in the tank. The exhaust gases are then vented outside the home. Considering that warm air is lighter than cool air, the exhaust gases will naturally rise and go out through the venting system. The optimal situation is to have the vent pipes be set up to go vertically out from the water heater, with no demand of any sort of blower to assist push the gases out. One still requires to be careful about backdrafting, which is when the exhaust fumes enter back into the house instead of leaving out the vent to the exterior. Likewise, standard atmospherically-vented water heaters are not as energy efficient as other more recent kinds that do not permit as much of the warm air produced to escape up through the vent pipes.

Among the category of direct vent water heaters there are various types we will not examine now, that can have different types of venting alternatives, like having a single or dual vent channel. Nevertheless, there are times when a blower is required to assist with the removal of the gases, which leads this discussion to power vent water heaters.

The following video explains in more detail the details of a direct vent system:

Power Vent Water Heaters
As can be presumed from above, power vent water heaters have a fan or blower connected to help with the removal of exhaust gases from the hot water heater. There are times that a water heater can not be installed where it is simple to install a vertical vent or chimney. Because a fan is utilized for removing the exhaust gases, the vent pipes can be installed either horizontally or vertically, or a combination of both.

The major benefit then for power venting is that ones water heater can be set up almost inside the house. An additional advantage is that generally PVC pipes can be made use of for the venting since the blower will cool the exhaust air enough that it will not be too hot for the PVC pipe to manage.

Some disadvantages with a power vent system is that it may cost some to at first install if the existing ventilation system is not in place. And, the equipment expense of the blower (though not that expensive) and if one requires to install a power outlet within six feet of the water heater’s position. It will make use of some electric power to run the blower but that also is not a big cost. Finally, the fans, depending upon the kind, run fairly silently, however some residents do not like the added ambient sound it makes. With the proper setup Water Heater Repair Philadelphia can help reduce the sound of the blower within the house.

In conclusion, there are a fair quantity of differences between direct and power vented water heaters. We suggest having a look at the ENERGY STAR details right here too in regards to the different energy efficiency ratings for the various kinds of heaters. In terms of which is best for your home ought to be chosen with a professional water heater replacement business.

Are Philadelphia Tankless Water Heaters Practical

Posted by on Jan 28, 2014 in Tankless Water Heater Repair Philadelphia, Water Heater Repair Philadelphia | 0 comments

There is a lot of discuss the advantages and disadvantages of tankless water heaters verses tank water heaters. Water Heater Repair Philadelphia is going to begin a discussion on tankless heaters today, pointing out a few of the claims and going over the realities. They have benefits and drawbacks over traditional water heaters and it might just depend upon exactly what ones specific usage requirements are that will determine which kind of the proper one for ones house. Heaters Water Heater Repair Philadelphia v

The standard theory of using a tankless water heater is among being energy efficient. Water is heated up as it is utilized, and not stored in the large tank of a standard water heater, regularly warmed so it is ready whenever it is to be utilized. Likewise, since they can hang on the wall and take up essentially no space at all, they are really practical.

Electrical Usage

Because tankless water heaters do require 240 volts of electricity and approximately 160 amps to establish, one may need to have ones electrical box upgraded to accommodate the power need of the system. For instance, and not to obtain excessively technical here, a standard tank water heater has around a 4500 watt heating element, verses four, 7000 watt elements of a whole-house tankless one.

As for efficiency, According to the Partnership for Advancing Technology in Housing (PATH), and supported by Housing and Urban Development (HUD), “further testing is needed to determine if electric tankless water heaters will match the efficiency of tank-type heaters.”

Appropriate Sizing

Tankless systems are sized by the flow rate determined in gallons per minute (GPM). One will have to identify when and what ones greatest demand of hot water is to correctly figure out the finest size device to get.

Below is the formula for figuring this out from Keltec Inc:

Flow rate (GPM)
Temperature rise ( T ºF)

Water Heater Repair Philadelphia PA

To determine the size and kilowatt rating you need, apply this formula:
“The result of this formula is the maximum kW needed to accomplish your project requirements for on-demand heated water. Other media will vary slightly. This formula is a nearly universal method of calculation for energy input to yield temperature at required water flow.”

Water Quality on the Tankless System

The quality of the water one has at home should be analyzed also in order to get the most from a tankless water heater. If ones water is high in mineral content, like calcium, they will build up on the coils gradually and reduce the life expectancy of the unit. If the water hardness at ones home is above 11 grains per gallon, a water softener would be advised. Producers do include de-liming directions and usually have a warning light on the system to determine when this should be performed. Nonetheless, keep in mind what the manufacturers guarantee covers. If it is just against manufacturer’s defect, this will not cover any repairs needed due to ones water quality. In optimal conditions, a tankless system will last much longer than a conventional water heater, which can assist validate the higher preliminary equipment cost and installation costs, but one will have to bear in mind keeping it running correctly to make back ones financial investment.

Service and Repair Costs

These costs are usually higher for a tankless system than a standard water heater, just to have a heads up. Many individuals normally do not have their traditional water heater services too regularly (sadly) but it is suggested to have a tankless unit expertly serviced once a year.

Instantaneous Hot Water

This should not be that huge of a deal, but though manufacturers do market instantaneous hot water. Undoubtedly one realized that it takes a moment for the hot water being heated immediately to go through ones hot water pipe to the faucet or shower. Though, if one is just using the faucet a little the tankless heater’s burner may not fire up if the faucet is not opened up more. As an example, a flow rate of one-half gallons to 2 gallons per minute is needed for electric tankless heaters to heat water.

Depending upon the quantity of hot water one needs at the very same time, even more than one unit will require to be installed. This is easy to do, however clearly increases the equipment costs while doing so.

Equipment and Set Up Costs

An average cost range for tankless heaters is around $800 to $1200. A normal storage tank water heater it is around $300 to $500. Set up expenses are about $1200 and $300 respectively then too. One will, once again, most likely require an electrical upgrade, in addition to a different gas pipe setup (if utilizing a gas tankless heater), and a brand-new ventilation system. An advantage of changing ones water heater with a system comparable to the existing one is many of these upgrades will not be needed – they are currently st up.

Advantages of Going Tankless

No stored water, which in itself has numerous benefits. First, if there was to be a leak with a tank heater, there could possibly be water damage to ones house. Likewise, one ought to flush the tank at least when a year to keep mineral build up reduced, however there is the potential for smelly water smells, bad tasting water, and the development of legionella bacteria in the tank if it is not at a sufficient temperature. Traditional water heaters take up far more space also.

The previous video shows the advantages of tankless water heaters and this video expresses some of the drawbacks of tankless water heaters:

Efficiency

Here is what Consumer Reports has found: “Gas tankless water heaters, which use high-powered burners to quickly heat water as it runs through a heat exchanger, were 22 percent more energy efficient on average than the gas-fired storage-tank models in our tests. That translates into a savings of around $70 to $80 per year, based on 2008 national energy costs. But because they cost much more than storage water heaters, it can take up to 22 years to break even longer than the 20-year life of many models. Moreover, our online poll of 1,200 readers revealed wide variations in installation costs, energy savings, and satisfaction.”

The Center for Energy and Environment says that “A 37% savings of water heating energy per household was found for replacing a typical natural draft storage water heater with a tankless one. However, this savings was not enough to offset the high incremental cost resulting in paybacks from 20 to 40 years.”

Finally, the National Rural Electric Cooperative Association concludes that “Tankless water heaters generally aren’t as energy efficient as well-kept tank water heaters. Insulation, temperature setback, timers, and heat traps can all lower energy costs with tank water heaters.”

One point to weigh is that yes, tankless systems will utilize less gas than a conventional gas water heater which does have its ecological benefits. However, a great deal of electricity is utilized, for electricity takes longer to heat up water than gas. And, the majority of electrical power is produced from burning nonrenewable fuel sources.

Conclusions

As with any sort of technology, the field of water heating is ever progressing. Efficiency advances are increasing with traditional gas and especially electric storage tank water heaters. There are various benefits with tankless and standard heaters that one will require to consider. Do not think twice to let Water Heater Repair Philadelphia know of any concerns you might have in the choice process.

Check out our Tankless Water Heater Repair Philadelphia page too!

Polar Vortex vs Your Philadelphia Water Heater

Posted by on Jan 7, 2014 in Leak Detection Philadelphia, Water Heater Repair Philadelphia | 0 comments

So with Polar Vortex upon us, let Water Heater Repair Philadelphia see to it ones water heater and pipes will survive its fury! Nationwide, over 250,000 Americans normally have some sort of damages to their homes due to flooding from split plumbing. With this sort of cold weather condition we are experiencing now, that number may are greater.

Here’s the big picture from The Weather Channel (click the name for the latest weather information):

As soon as outdoor temperature levels go below 20 degrees is when pipes can begin to freeze. Definitely, numerous parts of the nation are experiencing temperature levels much lower than that, and parts of the country that normally do not experience temperatures that reduced!

The Polar Vortex is breaking temperature records. For most places, it is the coldest it has been in over 20 years—Illinois, Indiana, George, Virginia, Oklahoma, Texas and New York all posted record lows (via Fox News).

So how does one help avoid pipes from freezing and breaking?

There are two methods to do so. The first is to avoid heat loss from the water inside ones pipes. The second is to ensure there is space for growth inside a water pipe in case ice kinds. If you have city water, the primary pipes that provide the water are normally deep enough to avoid freezing; nevertheless, once the water lines are at the ground surface area level when they reach ones home, is when the issues begin.

Insulation is the name of the game!

Insulation is not simply for the hot water pipes, however the cold water lines too. Even pipes inside the house – those in the attic, basement, a crawl space – must be covered in foam pipe insulation or covered in pipe insulation tape. Places where it will definitely be cold, like in a garage, is the water heater located there, electrical heat tape can be utilized.

It can be practical to leave cabinet doors in the kitchen and restrooms open to assist with the warm air flow of the home to keep water pipes a little warmer too. Make sure to keep the garage door closed and any vents into a crawl space shut too.

Leaving faucets open a little so a drip of water can run through them can assist. It will help ease the develop up of pressure in the pipes, though it is not a complete security versus a frozen pipe. Heck, even falls freeze!

As for the water heater, many companies make water heater blanket kits that fit around the tank. There can be very helpful in helping the water heater keep the heat inside the tank, so the system is not having to constantly go to keep its set temperature level. This, obviously, also assists save energy dollars too!

Make certain one knows where the water turned off valve is found in the house in case a water pipe does rupture, one can turn the water off to avoid significant water damage.

According to CNN, “The record cold in many areas is putting a strain on electric grids — creating dangers that more people could lose power.”

Water Heater Repair Philadelphia suggests making sure one is ready in the case of a power outage, especially with these record low temperatures!

Polar Vortex

Source: NOAA/NASA GOES Project

Community Resources:

City of Philadelphia Water Department

Toilet Terminology

Posted by on Dec 28, 2013 in Toilet Repair Philadelphia, Water Heater Repair Philadelphia | 0 comments

With half of the December holiday season behind us, Water Heater Repair Philadelphia chose to have a little fun this week and desired to share a new infographic by Phil Luther with you. It is precisely 7 months to the 104th anniversary of John Crapper’s death (July 27), the individual to whom the innovation of the flush toilet is typically connected with. Actually, in 1596 John Harrington created the contemporary flush toilet, though Crapper did further the development of the toilet and held lots of essential plumbing patents that made commodes work much better and in a more sanitary means.

Your toilet might be working a little overtime this holiday period if you have had great deals of visitors and family in from out of town. We suggest for everybody to be watchful of what all gets flushed so you will not have to call us for any toilet repairs. Attempt to keep a wastebasket in plain sight beside the toilet so visitors will use it and not flush items that you would not normally flush yourself … maybe keep a plunger in plain sight too, simply in case.

Take pleasure in the list of synonymous terms for the word “toilet” below and take pleasure in the rest of the period!

Toilet Repair Philadelphia

How to Get Rid of Philadelphia Water Heater Odors

Posted by on Dec 10, 2013 in Water Heater Repair Philadelphia | 0 comments

If you have foul-smelling water originating from your water heater follow Water Heater Repair Philadelphia’s directions below to obtain your water smelling and tasting much better.

The Causes of Philadelphia Water Heater Smells?

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more: http://www.soquelcreekwater.org/content/how-get-rid-odor-water

The most common reason for hot water smell is germs in the water system.
This is more widespread in houses that use well water and cities that utilize wells as their water source.

Setting your water heater temperature at 140 degrees or above must help cut down on germs development.

Ways to remove foul water.

The directions are for cleaning your water heater with chlorine bleach (clorox).

Turn off the electric or gas supply to the tank.

Turn off the cold water supply to the tank.

Open the hot side of the kitchen faucet to enable air to enter the tank.

Connect a garden hose to the drain valve and drain water heater.

Close the drain valve.

Now you need a way to obtain the bleach into the tank.
If your water heater has a flexable line where cold water enters the tank, unscrew the line from the tank.
If not, remove the pressure relief valve. An aspect could be gotten rid of from an electric water heater.

Utilize a funnel to pour the bleach into the opening.
Use 5 ounces of bleach for every gallon of the tank capacity.
Example – A 50 gallon water heater would need 250 ounces of bleach (about 2 gallons).

Reinstall the water line or relief line.

Refill the tank with water.

Close the hot side of the kitchen area faucet as soon as all the air is out of the line.

Run all hot water components (consisting of the dishwasher and garments washer) up until you smell bleach.
The concept is to get rid of the germs in the water lines also.

Let the water stand in the water heater tank and water lines undisturbed for a couple of hours.

Drain your tank once more and refill it. Let it set undisturbed for 30 minutes and drain the one more time.

Refill the tank. Open all the hot water components and let them run till the scent of bleach is gone including the dishwasher and clothing washer.

Gas Water Heaters
Relight the water heater pilot burner.

Electric Water Heaters
Turn the power back on.

If the drain valve obstructs up when your tring to drain the tank go to the flush hot water heater page to see how you can change the drain valve with a ball valve.

You might have to duplicate this treatment more than when however normally one time cares for foul water or water heater odor.

Also, by changing ones anode rods, and even the type used can do the trick as the following video illustrates:

More Resources

Controlling Odors in Hot Water Heaters – City of Fellsmere

Solving rotten-egg odor in water heaters

Your Household Water Quality: Odors in Your Water

How Thermocouples Work on Ones Philadelphia Water Heater

Posted by on Dec 9, 2013 in Water Heater Repair Philadelphia | 0 comments

Ok, not to get too technical with you today, but Water Heater Repair Philadelphia wants to share some information on a water heater’s thermocouple.

The Family Handyman correctly concluded that “when thermocouples wear out, the pilot light goes out, the burner won’t light, and you don’t get any hot water.”

Standard style
Also called universal water heater thermocouple. It screws into below the gas valve and a probe on the other end slides into a holding bracket near the pilot light. It looks like a piece of copper wire.

Universal thermocouples are available in lengths from 15 to 36 inches. An 18 or 24 inch will be enough for all domestic water heaters utilizing universal kits. Nearly all older waters heaters and many of the newer design systems with a closed burner compartment and a seeing window will utilize this thermocouple.
If you wish to make use of an exact replacement length just eliminate your old one and measure it.

TCO design

Thermal Cut Off style has a re-settable thermal shut off switch indispensable into the thermocouple. In case of a flash fire or blow back from the burner the TOC will shut down gas flow to the burner and pilot. In case of a shut down the TOC needs to reset itself after it cools off and enable you to relight the pilot. The TOC switch looks like a watch battery. You will only find the TOC on newer design water heaters with seal burner compartments.

TOC non-resettable style

These thermocouples have a small TOC build inside the tube. They look just like a basic one other than the diameter is bigger about midways of television. When these TOC’s turn off they will not reset and should be replaced.

Exactly how Thermocouples Work

A pilot thermocouple sends a small electrical current to the gas valve when the probe is warmed to a specific temperature level. This electrical current informs the gas valve that the pilot is lit and its ok to send out gas to the burner if the thermostat requires it.  There are some great images to illustrate how this works here.

To test  a water heater thermocouple press the pilot button down on the water heater gas control valve. Then light the pilot. If after holding the pilot button down 30 to 60 seconds the pilot light goes out when you let go of the button, the thermocouple is most likely at fault on older devices. The TOC or air flow can be the trouble on newer systems with a pilot light viewing window.

If the pilot does not light at all the problem is gas flow, gas control valve, TOC tripped.

Usual Thermocouple Problems

The most usual trouble is the suggestion on the thermocouple probe weakens. It can quickly be replaced.

Thermocouple Repair

If the probe appears white in color this is carbon build up. It could keep the probe from getting hot enough to send a signal to the gas valve. Try sanding it with emery cloth and relight the pilot. It ought to work for a while however keep a brand-new thermocouple convenient.

  • The thermocouple probe need to be in the pilot light flame.
  • The thermocouple needs to be screwed into the gas valve firmly.
  • Check the pilot thermocouple tube for kinks.

Water Heater Repair Philadelphia hopes this has actually been an excellent intro to a water heater’s thermocouple for you!

Philadelphia Water Heater Safety Precautions

Posted by on Dec 4, 2013 in Plumbing Contractors Philadelphia, Water Heater Repair Philadelphia | 0 comments

Effectively keeping ones water heater is essential not so it works to its full capacity and can save some energy money, but for safety issues too. Yes, it can explode – it does not occur too often for residents, however obviously this is something that Water Heater Repair Philadelphia does not want to have take place to you!

Vents
Venting can be sort of technical but we will go over the fundamentals below. The vent need to be the exact same diameter as the draft diverter of the water heater tank. It is expected to increase and out (for atmospherically vented heaters). Not other directs like up, down, up and out. For direct-vent water heaters, the vent need to go out a side wall. As for power-vent heaters, the fan blows the fumes out, so there is some versatility in the direction they are vented.

Any roof or wall that the vent goes through need to be a double wall. The single wall pass throughs must be screwed with 3 screws per area. If these fundamentals are not adhered to, the vents can fall apart gradually and carbon monoxide gas can cause significant troubles within ones house. Naturally we don’t desire that to occur!

The only other interested in venting is that of backdrafting. The fumes can eat the vents with acid condensation. If enough of this gets on cold piping and the water heater it will not be a great situation for a properly working water heater. If the fumes go back inside the instead of being correctly vented outside, the fumes can enter the living locations of the house. Soot issues can emerge as well.

Dielectric Connectors
The steel water heater is linked to cooper pipes by the dielectric connectors. When 2 these 2 metals are assembled in water electrolysis occurs. The process wears away one metal away to safeguard the other. This procedure is crucial in protecting the inside of the water heater. Evaluation for leaks must be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a fundamental part of the water heater, for it assists to ensure the darn thing does not explode under pressure if the temperature surpasses the appropriate limitations the water heater is developed for. Once a year (a minimum of) the T&P valve need to be examined to ensure, it is working correctly, for they can be susceptible to failure. Just lifting up on the handle water should flow freely out and stop when the handle is released. If it just runs or trickles, or does absolutely nothing at all, it will need to be changed.

The drain lines for the T&P line must not be routed up, because water does not stream uphill too well. Ensure it goes down and or out please. If water is running out the drain line routinely, it is the indication of something incorrect too. It can be one of numerous various things that we will not enter below – simply get in touch with a local plumbing technician please.

Earthquake Straps
Yep, even if you don’t reside in an earthquake zone and are required to have these on ones water heater, it is a pretty good idea to do so. It appears like most all brand-new houses in sub-divisions nowadays have the water heater in the garage. Yes, there is normally a concrete curb in front of it so one does not drive a vehicle into it, but things can unintentionally knock it over so be safe and strap that say thanks to in.

Temperature Level Setting
It appears most residential water heater tanks have settings of warm – hot – extremely hot … and not degree markings. Some “suggestions” on conserving energy at home specifically in the winter season time, say to decrease the setting on the tank to 120 degrees. That’s wonderful for conserving energy however legionella microorganisms, which causes Legionnaire’s disease can expand at 120 degrees. By breathing in the mist from the water in the shower, one can inhale the bacteria. Search for a medium between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature level so be careful.

Anode Rods
These generally are made from aluminum and there is nothing incorrect with that in concept, though we recommend using magnesium ones. Let’s state for whatever reason there is some kind of emergency or catastrophe where one lives and one had to make use of the water in the water heater for drinking water (since lots of emergency preparedness people advise doing this). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be packed with aluminum substances, which is not great for the body. It is bad for the stomach, intestines and joints.

The anodes aid with rust defense and are crucial in prolonging the life of the water heater. They can likewise aid with odor troubles with the water. Generally, magnesium anodes just work better for lots of various reasons like the wellness benefits, let construct up of sediment, a quieter water heater, and they often work much better with softened water.

Drain Valve
Ok, just examine it at least yearly to make certain the darn thing opens and works. And it is excellent to drain and purge the tank at least once a year anyway (something you naturally are doing already). If for some reason one should use the water during a catastrophe or drain it to quite a noisy tank and have actually not drained it frequently, and it does not open, it will take longer to remedy the problem you are initially attempting to fix.

Combustion Changer Hatch
Given that gas and oil water heaters breathe the air drawn in from below, combust with it and exhale it, it is very important to keep the location around it, specifically below the water heater, clean and swept. If if is not burning appropriately, it can cause composing issues (pointed out above), as well as combustion and fume problems and potentially be a fire hazard. A few of examining the chamber and how the flame burns is objective so we are not going to enter a great deal of information right here. it is essential to see if the combustion chamber roof has a great deal of rust or water markings or is black in color. These are not a great sign at all. One need to see some blue flame at the bottom when it burns and orange and yellow at the top, nonetheless, the yellow should not be extremely high up. One must see grey metal, some white condensation marks are ok.

Water Heater Repair Philadelphia has put together an infographic to highlight the information above:

Water Heater Repair Philadelphia